12-138 preliminary high sensitivity, high speed photocoupler 6n138 series 6n138 6n138m 6n138s 6N138S-TA 6N138S-TA1 6n138-v 6n138m-v 6n138s-v 6n138sta-v 6n138sta1-v part number package application part number 8-pin dip 8-pin (leads with 0.4" spacing) 8-pin (lead bends for surface mount) 8-pin (tape and reel packaging of type i) 8-pin (tape and reel packaging of type ii) 8-pin dip 8-pin (leads with 0.4" spacing) 8-pin (lead bends for surface mount) 8-pin (tape and reel packaging of type i) 8-pin (tape and reel packaging of type ii) 6n138 6n138 features high current transfer ratio ( ctr : min. 300% at i f = 1.6ma ) high speed response ( t phl : typ. 2 s at r l = 2.2k ) instantaneous common mode rejection voltage ( cm h : typ. 500v/ s ) ttl compatible output options available : - leads with 0.4" (10.16mm) spacing (m type) - lead bends for surface mounting (s type) - tape and reel of type i for smd (add "-ta" suffix) - tape and reel of type ii for smd (add "-ta1" suffix) - vde 0884 approvals (add "-v" suffix) applications 1. interfaces for computer peripherals 2. electronic calculators, measuring instruments, control equipment 3. telephone sets 4. signal transmission between circuits of different poten- tials and impedances package dimensions notes : 1. year date code. 2. 2-digit work week. 3. factory code shall be marked (z taiwan, y thailand). 4. all dimensions are in millimeters (inches). 5. tolerance is 0.25mm (.010") unless otherwise noted. 6. specifications are subject to change without notice. ordering information
preliminary photocoupler 12-139 ratings and characteristics absolute maximum ratings (ta=25 ) input output *1. ac for 1 minute, r.h. = 40 ~ 60% isolation voltage shall be measured using the following method. (1) short between anode and cathode on the primary side and between collector and emitter on the secondary side. (2) the isolation voltage tester with zero-cross circuit shall be used. (3) the waveform of applied voltage shall be a sine wave. *2. for 10 seconds electrical / optical characteristics ( ta = 0 ~ +70 unless otherwise specified ) *1.isolation voltage operating temperature storage temperature *2.soldering temperature parameter ma v mw v v v ma mw vrms 20 5 35 -0.5~+7 -0.5~+7 0.5 60 100 2,500 0~+70 -55~+125 260 i f v r p v cc v o v ebo i o p o v iso t opr t stg t sol symbol rating unit forward current reverse voltage power dissipation supply voltage output voltage emitter-base reverse withstand voltage (pin 5 to 7) average output current power dissipation input forward voltage input forward voltage temperature coefficient input reverse voltage input capacitance *1 current transfer ratio logic (0) output voltage logic (1) output current logic (0) supply current logic (1) supply current *2 leak crrent (input-output) *2 isolation resistance (input-output) capacitance (input-output) propagation delay time output (1) (0) propagation delay time output (0) (1) *3 instantaneous common mode rejection voltage output(1) *3 instantaneous common mode rejection voltage output(0) parameter symbol min. typ. max. unit conditions ta=25 , i f =1.6ma i f =1.6ma ta=25 , i r =10 a v f =0, f=1mhz i f =1.6ma, v o =0.4v v cc =4.5v i f =1.6ma v cc =4.5v i o =4.8ma i f =0, v cc =v o =7v i f =1.6ma, v cc =5v v o =open i f =0, v cc =5v, v o =open ta=25 , 45%rh t=5s, v i-o =3kv dc v i-o =500v dc f=1mhz i f =1.6ma, r l =2.2k i f =0, v cm =10v p-p rl=2.2k v cm =10v p-p , i f =1.6ma r l =2.2k v mv/ v pf % v a ma a a pf s v/ s v/ s 1.7 0.4 250 1.5 10 1.0 10 35 1.1 -1.9 60 1600 0.1 0.1 0.4 0.01 10 12 0.6 5 14 500 -500 5.0 300 v f v f / t a bv r c in ctr v ol i oh i ccl i cch i i-o r i-o c i-o t phl t plh cm h cm l *1. current transfer ratio is the ratio of input current and output current expressed in %. *2. measured as 2-pin element ( short 1, 2, 3, 4 and 5, 6, 7, 8 ) *3 instantaneous common mode rejection voltage "output (1)" represents a common mode voltage variation that can hold the output above (1) level (vo>2.0v). instantaneous common mode rejection voltage "output (0)" represents a common mode voltage variation that can hold the output above (0) level (vo<0.8v).
12-140 preliminary typical electrical/optical characteristic curves (25 ambient temperature unless otherwise noted)
preliminary photocoupler 12-141
|
